Publications
Momber A.W.:
Corrosion and Corrosion Protection of Wind Power Structures in Marine Environments – Vol. 1: Introduction and Corrosive Loads
Elsevier / Academic Press (2024), ISBN: 978-0-323-85742-0
https://doi.org/10.1016/C2020-0-01629-4
Momber, A.W.:
Corrosion and Corrosion Protection of Wind Power Structures in Marine Environments – Vol. 2: Corrosion Protection Measures
Elsevier / Academic Press (2024), ISBN: 978-0-323-85744-4
https://doi.org/10.1016/C2020-0-01827-X
Blawert, C., Serdechnova, M., Bertram, J., Momber, A.W., Konchakova, N., Höche, D., Zheludkevich, M.L.:
Effects of mechanical surface pre-treatment on integrity and corrosion of bare and coated AA6082 substrates
Journal of Materials Research and Technology, Vol. 31 (2024), 844-859
https://doi.org/10.1016/j.jmrt.2024.06.097
Momber, A.W., Irmer, M., Kelm, D., Cherewko, V.:
Damage morphology and force-deflection curves for impact loading of thick multilayer organic protective coating systems
Journal of Coatings Technology and Research, Vol. 21 (2014), 857-878
https://doi.org/10.1007/s11998-023-00829-9
https://doi.org/10.1007/s11998-023-00908-x
Momber, A.W., Marquardt, T., Kelm, D., Irmer, M.:
Effects of impact damages on the performance of offshore wind power coatings after accelerated aging
Corrosion Engineering Science and Technology (2024)
https://doi.org/10.1177/1478422X241246345
Irmer, M., Kelm, D., Marquardt, T., Momber, A.W., Eiben, K., Buchbach, S.:
The performance of a self-adherent foil system for the corrosion protection of steel substrates for offshore wind tower structures
Materials and Corrosion (2024)
https://doi.org/10.1002/maco.202314218
Momber, A.W., Marquardt, T., Irmer, M., Kelm, D.:
Effects of compressive damage on the corrosion protection performance of offshore wind power coating systems
Materials and Corrosion (2023)
https://doi.org/10.1002/maco.202314074
Marquardt, T., Krenz, A., Momber, A.W., Buchbach, S.:
The applicability of stripe light projection data to the determination of fractal dimensions of blast-cleaned steel surfaces
International Journal of Adhesion and Adhesives, Vol. 131 (2024), 103639
https://doi.org/10.1016/j.ijadhadh.2024.103639
Momber, A.W., Plagemann, P., Marquardt, T., Buchbach, S.:
EIS offset-cell measurements on epoxy-based coating systems over mechanically and thermally rounded cut edges
Progress in Organic Coatings, Vol. 187 (2024), 108140
https://doi.org/10.1016/j.porgcoat.2023.108140
Kelm, D., Marquardt, T., Momber, A.W., Sellmeyer, S., Irmer, M.:
Statistical investigations into automated spray-applied stripe coats to complex geometries of floating offshore wind foundations
Materials and Corrosion (2024)
https://doi.org/10.1002/maco.202314140
Marquardt, T., Momber, A.W., Krenz, A.:
Measurement methods and fractal dimensions of blast-cleaned steel substrates
Surface Engineering, Vol. 39[6] (2023), 780-796
https://doi.org/10.1080/02670844.2023.2259527
Shojai, S., Schaumann, P., Momber, A.W., Ghafoori, E.:
Fatigue stress concentrations analysis of real corroded steel structures based on replica imprints
Proceedings in Civil Engineering (ce papers) Vol. 6[3-4] (2023), 2527-2533
https://doi.org/10.1002/cepa.2568
Marquardt, T., Momber, A.W.:
The determination of fractal dimensions of blast-cleaned steel substrates by means of comparative cross section image analysis and contact stylus instrument measurements
Journal of Adhesion Science and Technology, Vol. 37[15] (2023), 2175-2194
https://doi.org/10.1080/01694243.2022.2118567
Momber, A.W., Irmer, M., Kelm, D.:
Response of corrosion protection coating systems for offshore components to high compressive loads during lifting
Materials and Corrosion, Vol. 74[9] (2023), 1272-1288
https://doi.org/10.1002/maco.202313835
Momber, A.W., Langenkämper, D., Möller, T., Nattkemper, T.W.:
The exploration and annotation of large amounts of visual inspection data for protective coating systems on stationary marine steel structures
Ocean Engineering, Vol. 278 (2023), 114337
https://doi.org/10.1016/j.oceaneng.2023.114337
Marquardt, T., Momber, A.W.:
Classified substrate roughness parameters of blast-cleaned steel substrates and their effects on fractal dimensions
Journal of Adhesion Science and Technology, Vol. 37[7] (2023), 1233-1255
https://doi.org/10.1080/01694243.2022.2071045
Andresen-Paulsen, G., Braun, M., Marquardt, T., Momber, A.W., Ehlers, S.:
The integrity of corrosion protection systems of welded maritime structures under cyclic loading
Advances in the Analysis and Design of Marine Structures (eds: J. W. Ringsberg, C. Guedes Soares), CRC Press, London
https://doi.org/10.1201/9781003399759-80
Marquardt, T., Momber, A.W.:
The assessment of fractal dimensions with the direct use of scanning electron microscopy (SEM) images from blast-cleaned steel substrates
Journal of Adhesion Science and Technology, Vol. 37[1] (2023), 16-37
https://doi.org/10.1080/01694243.2021.2013057
Momber, A.W., Langenkämper, D., Möller, T., Nattkemper, T.W.:
Eine Online-Plattform für die Verarbeitung digitaler visueller Daten zur Zustandsbeschreibung von Beschichtungssystemen an maritimen Stahlbauten
Stahlbau, Jg. 92[2] (2023), 62-67
https://doi.org/10.1002/stab.202200080
Buchbach, S., Marquardt, T., Momber, A.W.:
Windenergieanlagen bekleben statt beschichten
Journal für Oberflächentechnik, Vol. 62 [Suppl. 5] (2022), 10-13
https://doi.org/10.1007/s35144-022-2303-x
Momber, A.W., Irmer, M.
Distribution parameters of a plastic–elastic transition function for normal force effects on the abrasive wear of organic coatings
Journal of Coatings Technology and Research, Vol. 19 (2022), 1909-1911
https://doi.org/10.1007/s11998-022-00673-3
Momber, A.W., Wilms, M., Brün, D.:
The use of meteorological and oceanographic sensor data in the German offshore territory for the corrosion monitoring of marine structures
Ocean Engineering, Vol. 257 (2022), 110994
https://doi.org/10.1016/j.oceaneng.2022.110994
Momber, A.W., Marquardt, T., Buchbach, S., Plagemann, P.:
The corrosion protection performance of repair coatings for offshore wind power constructions after long-term splash zone site exposure
Materials and Corrosion, Vol. 73[4] (2022), 526-539
https://doi.org/10.1002/maco.202112864
Momber, A.W., Nattkemper, T.W., Langenkämper, D., Möller, T. Brün, D., Schaumann, P., Shojai, S.:
A data-based model for condition monitoring and maintenance planning for protective coating systems for wind tower structures.
Renewable Energy, Vol. 186 (2022), 957-973
https://doi.org/10.1016/j.renene.2022.01.022
Momber, A.W., Krenz, A., Buchbach, S.:
The corrosion of carbon steel under delaminating repair coatings after long-term marine splash zone exposure.
Materials and Corrosion (2022), DOI: 10.1002/maco.202112942
https://doi.org/10.1002/maco.202112942
Momber, A.W., Möller, T., Langenkämper, D., Nattkemper, T.W., Brün, D.:
A Digital Twin concept for the prescriptive maintenance of protective coating systems on wind turbine structures
Wind Engineering, (2021), DOI: 10.1177/0309524X211060550
https://doi.org/10.1177/0309524X211060550
Momber, A.W., Marquardt, T., Buchbach,S., Plagemann, P.:
The corrosion protection performance of repair coatings for offshore wind power constructions after long-term splash zone site exposure.
Materials and Corrosion, (2021), DOI: 10.1002/maco.202112864
https://doi.org/10.1002/maco.202112864
Momber, A.W., Nattkemper, T.W., Langenkämper, D., Möller, T., Brün, D., Schaumann, P., Shojai, S.:
Digitalisierung und Verarbeitung von Sensordaten für die Zustandsbewertung von Oberflächenschutzsystemen stählerner Türme von Onshore‐Windenergieanlagen.
Stahlbau, Jg. 90[7] (2021), 528-541
https://doi.org/10.1002/stab.202100020
Momber, A.W., Fröck, L., Marquardt, T.:
Effects of adhesive type on the mechanical properties of adhesive joints between polyurethane top coats and polyurethane-based adhesives after accelerated atmospheric ageing.
Marine Structures, Vol. 79 (2021), 103022
https://doi.org/10.1016/j.marstruc.2021.103022
Momber, A.W., Irmer M.:
Taber abrasive wear resistance of organic offshore wind power coatings at varying normal forces.
Journal of Coatings Technology and Research (2021), DOI: 10.1007/s11998-020-00437-x
https://doi.org/10.1007/s11998-020-00437-x
Schaffarczyk, A.P., Momber, A.W., Stenzel, V.:
Wind tunnel investigations of DU97-W-300-mod equipped with riblets.
Wind Energy (2021), DOI: 10.1002/we.2622
https://onlinelibrary.wiley.com/doi/10.1002/we.2622
Irmer, M., Momber, A.W., Marquardt, T., Flügge, W.:
Impact damages to organic coating systems of offshore wind turbines – corrosion progress and repair strategies.
Developments in Renewable Energies Offshore (ed. C. Guedes Soares), CRC Press, London, 2020
https://doi.org/10.1201/9781003134572-41
Momber, A.W., Fröck, L., Marquardt, T.,:
Effects of accelerated ageing on the mechanical properties of adhesive joints between stainless steel and polymeric top coat materials for marine applications.
International Journal of Adhesion and Adhesives, Vol. 103 (2020), 102699
https://doi.org/10.1016/j.ijadhadh.2020.102699
Momber, A.W., Fröck, L., Marquardt, T.,:
Nachträgliches klebtechnisches Fügen von Haltern auf Beschichtungen mit ungenügender Haftfestigkeit.
Stahlbau, Jg. 89 (2020), DOI: 10.1002/stab.202000066
https://doi.org/10.1002/stab.202000066
Momber, A.W., Irmer, M., Marquardt, T.:
Effects of polymer hardness on the abrasive wear resistance of thick organic offshore coatings.
Progress in Organic Coatings, Vol. 146 (2020), 105720
https://www.sciencedirect.com/science/article/pii/S030094402030415X
Momber A.W., Fröck L., Marquardt T.:
Nachträgliches klebtechnisches Fügen von Haltern auf bereits beschichtete Stahloberflächen.
Stahlbau, Jg. 89 (2020), DOI: 10.1002/stab.202000020
https://onlinelibrary.wiley.com/doi/abs/10.1002/stab.202000020
Momber, A.W., Irmer, M., Glück, N.:
Investigation into the performance of a dual-layer thin-film organic coating during accelerated low-temperature offshore testing
ASCE Journal of Offshore Mechanics and Arctic Engineering, Vol. 139 (2017), Paper 041402, 1-9
http://offshoremechanics.asmedigitalcollection.asme.org/article.aspx?articleid=2612228
Momber, A.W., Irmer, M., Glück, N.:
Effects of accelerated low-temperature ageing on the performance of polymeric coating systems on offshore steel structures
Cold Regions Science and Technology, Vol. 140 (2017), 39-53
https://www.sciencedirect.com/science/article/pii/S0165232X16303202
Momber, A.W., Buchbach, S., Plagemann, P., Marquardt, T.:
Edge coverage of organic coatings and corrosion protection over edges under simulated ballast water tank conditions
Progress in Organic Coatings, Vol. 108 (2017), 90-92
https://www.sciencedirect.com/science/article/pii/S0300944016310463
Momber, A.W., Marquardt, M.:
Protective coatings for offshore wind energy devices (OWEAs): a review.
Journal of Coatings Technology and Research, Vol. 15 (2018), 13-40
https://link.springer.com/article/10.1007/s11998-017-9979-5
Momber, A.W.:
Statistical effects of surface preparation and coating type on the corrosion protection performance of repair coatings for offshore wind power constructions
Materials and Corrosion, Vol. 69 (2018), 460-471
https://onlinelibrary.wiley.com/doi/abs/10.1002/maco.201709765
Momber, A.W., Irmer, M., Glück, N.:
A note on the distribution of stationary contact angles on organic coatings.
International Journal of Adhesion and Adhesives, Vol. 72 (2017), 1-5.
http://www.sciencedirect.com/science/article/pii/S0143749616301798
Momber, A.W., Buchbach, S., Plagemann, P., Marquardt, T.:
Effects of edge treatment parameters on the protection performance of organic coating systems in a wave chamber.
Progress in Organic Coatings, Vol. 102 (2016), 167-177.
http://www.sciencedirect.com/science/article/pii/S0300944015303982
Momber, A.W., Buchbach, S., Plagemann, P., Marquardt, T.:
A statistical study into parameter effects on the coverage of organic coatings on rounded steel edges.
Progress in Organic Coatings, Vol. 101 (2016), 186-194.
http://www.sciencedirect.com/science/article/pii/S0300944016305823
Momber, A.W., Irmer, M., Glück, N.:
Hoar Frost Accretion on Organic Coatings Under Offshore Conditions.
ASME Journal of Offshore Mechanics and Arctic Engineering, Vol. 138[6] (2016), 064502
http://offshoremechanics.asmedigitalcollection.asme.org/article.aspx?articleid=2530159
Momber, A.W., Irmer, M., Glück, N., Plagemann, P.:
Corrosion Protection Performance of Organic Offshore Coating Systems at -60 °C Temperature Shock.
ASME Journal of Offshore Mechanics and Arctic Engineering, Vol. 138[6] (2016), 064501
http://offshoremechanics.asmedigitalcollection.asme.org/article.aspx?articleid=2530158
Momber, A.W., Irmer, M., Glück, N.:
Performance characteristics of protective coatings under low-temperature offshore conditions. Part 2: Surface status, hoarfrost accretion and mechanical properties.
Cold Regions Science and Technology, Vol. 127 (2016), 109-114.
http://www.sciencedirect.com/science/article/pii/S0165232X16300611
Momber, A.W., Irmer, M., Glück, N.:
Performance characteristics of protective coatings under low-temperature offshore conditions. Part 1: Experimental set-up and corrosion protection performance.
Cold Regions Science and Technology, Vol. 127 (2016), 76-82.
http://www.sciencedirect.com/science/article/pii/S0165232X16300520
Momber, A.W.:
Quantitative performance assessment of corrosion protection systems for offshore wind power transmission platforms.
Renewable Energy, Vol. 94 (2016), 314–327.
http://www.sciencedirect.com/science/article/pii/S0960148116302439
Momber, A.W., Plagemann, P., Stenzel, V.:
The adhesion of corrosion protection coating systems for offshore wind power constructions after three years under offshore exposure.
International Journal of Adhesion and Adhesives, Vol. 65 (2016), 96-101.
http://www.sciencedirect.com/science/article/pii/S0143749615001931
Momber, A.W., Irmer, M., Glück, N., Plagemann, P.:
Abrasion testing of organic corrosion protection coating systems with a rotating abrasive rubber wheel.
Wear, (2015) DOI: 10.1016/j. wear.2015.11.001.
http://www.sciencedirect.com/science/article/pii/S0043164815004640
Momber, A.W., Plagemann, P., Stenzel, V.:
Performance and integrity of protective coating systems for offshore wind power structures after three years under offshore site conditions.
Renewable Energy, Vol. 74 (2015), 606-617.
http://www.sciencedirect.com/science/article/pii/S0960148114005175
Irmer, M., Glück, N., Momber, A.W.:
Beschichtungssysteme: Verhalten unter arktischen Bedingungen.
Schiff & Hafen, Vol. 66 (2014) No. 9, 180-185.
http://www.schiffundhafen.de/publikationen/schiff-hafen/aktuell.html
Momber, A.W., Buchbach, S., Plagemann, P.:
Untersuchungen zum Korrosionsschutz von Kanten an Stahlkonstruktionen – Ergebnisse der Laborprüfungen (Teil 2).
Stahlbau, Vol. 81 (2012), No. 1, 41-48.
http://onlinelibrary.wiley.com/doi/10.1002/stab.201201502/abstract
Buchbach, S., Plagemann, P., Momber, A.W.:
Untersuchungen zum Korrosionsschutz von Kanten an Stahlkonstruktionen – Problemstellung und Versuchsdurchführung (Teil 1).
Stahlbau, Vol. 80 (2011), No. 1, 30-38.
http://onlinelibrary.wiley.com/doi/10.1002/stab.201001389/abstract
Momber, A.W.:
Corrosion and corrosion protection of support structures for offshore wind energy devices (OWEA).
Materials and Corrosion, Vol. 62 (2011), No. 5, 391-404.
http://onlinelibrary.wiley.com/doi/10.1002/maco.201005691/abstract
Teimouriana, H., Shabgarda, M.R., Momber, A.W.:
De-painting with high-speed water jets: Paint removal process and substrate surface roughness.
Progress in Organic Coatings, Vol. 69 (2010), 455-462.
http://www.sciencedirect.com/science/article/pii/S0300944010002353
Momber, A.W.:
Nachtrag zum Beitrag “Beurteilung von Korrosionsschutzsystemen für Offshore-Windenergietürme – Teil 2: Ergebnisse und Schlussfolgerungen“.
Stahlbau, Vol. 78 (2009), No. 11, 883-884
http://onlinelibrary.wiley.com/doi/10.1002/stab.200990153/abstract
Momber, A.W., Plagemann, P., Stenzel, V., Schneider, M.:
Beurteilung von Korrosionsschutz-systemen für Offshore-Windenergietürme – Teil 2: Ergebnisse und Schlussfolgerungen.
Stahlbau, Vol. 78 (2009), No. 6, 394-401.
http://onlinelibrary.wiley.com/doi/10.1002/stab.200910053/abstract
Momber, A.W., Plagemann, P., Stenzel, V., Schneider, M.:
Beurteilung von Korrosionsschutzsystemen für Offshore-Windenergietürme – Teil 1: Problemstellung und Versuchsdurchführung.
Stahlbau, Vol. 78 (2009), No. 4, 259-266.
http://onlinelibrary.wiley.com/doi/10.1002/stab.200910038/abstract
Momber, A.W., Plagemann, P., Stenzel, V., Schneider, M.:
Investigations into the corrosion protection of offshore wind energy towers: Part 3: Results of the laboratory investigations.
Journal of Protective Coatings and Linings, Vol. 26 (2009), No. 11, 38-46.
http://www.paintsquare.com/archive/?fuseaction=view&articleid=4037
Momber, A.W., Plagemann, P., Stenzel, V., Schneider, M.:
Investigations into the corrosion protection of offshore wind energy towers: part 2: Results of the site tests.
Journal of Protective Coatings and Linings, Vol. 26 (2009), No. 4, 24-34.
http://www.paintsquare.com/archive/?fuseaction=view&articleid=3731
Momber, A.W., Koller, S.:
Effects of surface preparation methods on delamination of organic coatings applied to a metal substrate.
Journal of Protective Coatings and Linings, Vol. 25 (2008), 43-52.
http://www.paintsquare.com/archive/?fuseaction=view&articleid=3211
Momber, A.W., Plagemann, P., Stenzel, V., Schneider, M.:
Investigations into the corrosion protection of offshore wind energy towers: Part 1: General situation and test programme.
Journal of Protective Coatings and Linings, Vol. 25 (2008), No. 4, 30-43.
http://www.paintsquare.com/archive/?fuseaction=view&articleid=3112
Stenzel, V., Plagemann, P., Momber, A.W.:
Les eoliennes offshore sont soumises a rude epreuve.
Galvanic – Organo, Vol. 771 (2007), 31-33.
http://cat.inist.fr/?aModele=afficheN&cpsidt=19978589
Godoy, R., Momber, A.W.:
Preparing offshore platforms with UHPAB – basics and cases.
Journal of Protective Coatings and Linings, Vol. 24 (2007), 36-47.
http://www.paintsquare.com/archive/?fuseaction=view&articleid=2801
Momber, A.W.:
Aspects of salt concentration of prepared steel substrates.
Journal of Protective Coatings and Linings, Vol. 23 (2006), No. 2, M2-M8.
http://www.paintsquare.com/archive/?fuseaction=view&articleid=2407
Momber, A.W., Koller, S.:
Zur Korrosionsschutzwirkung von organischen Beschichtungssystemen auf gestrahlten Stahloberflächen.
Stahlbau, Vol. 74 (2005), No. 10, 780-787
http://onlinelibrary.wiley.com/doi/10.1002/stab.200590177/abstract
Momber, A.W., Greverath, W.-D:
Surface preparation standards for steel substrates – a critical review.
Journal of Protective Coatings and Linings, Vol. 21 (2004) No. 2, 48-52.
http://www.paintsquare.com/archive/?fuseaction=view&articleid=1887
Momber, A.W., Koller, S., Dittmers, H.J.:
Effects of surface preparation methods on adhesion of organic coatings to steel substrates.
Journal of Protective Coatings and Linings, Vol. 21 (2004) No. 2, 44-50.
http://www.paintsquare.com/archive/?fuseaction=view&articleid=2042
Schaffarczyk, A.P., Momber, A., Stenzel, V.:
Wind tunnel investigations of DU97-W-300-mod equipped with riblets.
Wind Energy, (2021), DOI: 10.1002/we.2622
https://onlinelibrary.wiley.com/doi/10.1002/we.2622
Momber, A.W., Irmer, M.:
Taber abrasive wear resistance of organic offshore wind power coatings at varying normal forces.
Journal of Coatings Technology and Research, (2021), DOI: 10.1007/s11998-020-00437-x
Get in touch
At Muehlhan, we provide industrial services in more than 30 countries worldwide – we have a global presence but local roots.